Checkline WTT-110 Bedienungsanleitung PDF herunterladen

– 1 –

1.0 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 02

2.0 Unpacking and Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.0 Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.0 Charging the Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.0 AC Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6.0 Overview of Keypad and LCD Display . . . . . . . . . . . . . . . . . . . . . . . . . . .

7.0 Overview of Operating Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

8.0 Changing Units of Measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

9.0 General Operating Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

9.1 Additional Operating Information

10.0 Adjusting Advanced Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

10.1 Temperature Compensation

10.2 Selecting the Baud Rate of the RS232 Interface

10.3 Switching off the Auto-Power Off Function

10.4 Change the Refresh Rate of the Display

10.5 Flow Chart: Steps Required To Change Advanced Settings

11.0 Data Transfer (Model WT-110RS only) . . . . . . . . . . . . . . . . . . . . . . . . . . .

013

11.1 RS-232 Interface

11.2 Analog Output

12.0 Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

015

13.0 Troubleshooting Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

017

14.0 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

018

15.0 Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

019

16.0 Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

020

TABLE OF CONTENTS

– 20 –

16.0 Warranty

ELECTROMATIC Equipment Co., Inc. (ELECTROMATIC) warrants to the

original purchaser that this product is of merchantable quality and confirms in kind

and quality with the descriptions and specifications thereof. Product failure or mal-

function arising out of any defect in workmanship or material in the product existing at

the time of delivery thereof which manifests itself within one year from the sale of

such product, shall be remedied by repair or replacement of such product, at

ELECTROMATIC’s option, except where unauthorized repair, disassembly, tampering,

abuse or misapplications has taken place, as determined by ELECTROMATIC. All

returns for warranty or non-warranty repairs and/or replacement must be authorized by

ELECTROMATIC, in advance, with all repacking and shipping expenses to the

address below to be borne by the purchaser.

THE FOREGOING WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES,

EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO, THE WAR-

RANTY OF MERCHANTABILITY AND FITNESS FOR ANY PARTICULAR PUR-

POSE OR APPLICATION. ELECTROMATIC SHALL NOT BE RESPONSIBLE

NOR LIABLE FOR ANY CONSEQUENTIAL DAMAGE, OF ANY KIND OR

NATURE, RESULTING FROM THE USE OF SUPPLIED EQUIPMENT, WHETHER

SUCH DAMAGE OCCURS OR IS DISCOVERED BEFORE, UPON OR AFTER

REPLACEMENT OR REPAIR, AND WHETHER OR NOT SUCH DAMAGE IS

CAUSED BY MANUFACTURER’S OR

SUPPLIER’S NEGLIGENCE WITHIN ONE YEAR FROM INVOICE DATE.

Some State jurisdictions or States do not allow the exclusion or limitation of

incidental or consequential damages, so the above limitation may not apply to you.

The duration of any implied warranty, including, without limitation, fitness for any

particular purpose and merchantability with respect to this product, is limited to the

duration of the foregoing warranty. Some states do not allow limitations on how long

an implied warranty lasts but, not withstanding, this warranty, in the absence of such

limitations, shall extend for one year from the date of invoice.

ELECTROMACTIC Equipment Co., Inc.

600 Oakland Ave. Cedarhurst, NY 11516—USA

Tel: 1-800-645-4330/ Tel: 516-295-4300/ Fax: 516-295-4399

1 2 3 4 5 6 ... 10 11

Inhaltsverzeichnis

Seite 1 - ABLE OF CONTENTS

– 1 –1.0 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 022.0 Unpacking and Conten

Seite 2 - NTRODUCTION

– 10 –10.0 ADJUSTING ADVANCED SETTINGSThere are several adjustable settings that can be changed from the factory defaults tocustomize the WTT-110 to m

Seite 3 - PECIFICATIONS

ELECTROMATIC E Q U I P M E N T C O., I N C.600 Oakland Ave., Cedarhurst, NY 11516–U.S.A.TEL: 516-295-4300 • FAX: 516-295-4399 CHECK•LINE®INSTRUMENTSW

Seite 4 - PERATION

– 2 –1.0 INTRODUCTIONThank you for selecting the CHECK•LINE WTT-110 Wire Terminal Pull Tester foryour requirements. With correct use and proper care t

Seite 5 - 00..00 00

– 3 –2.0 UNPACKING & CONTENTSRemove the unit carefully and check the unit appears undamaged in shipment. Check to see that all of the supplied it

Seite 6 - ALIBRATION

– 4 –3.0 SETUPPlace the WTT-110 Wire Terminal Tester on a level and stable work area where theuser can perform the testing in a comfortable manner. Th

Seite 7 - ENERAL OPERATING PROCEDURES

– 5 –6.0 OVERVIEW OF KEYPAD & LCD DISPLAY1 Low Battery Indicator. Flashes when batteries need charging, turns off when fully charged. Remains on

Seite 8

– 6 –7.0 OVERVIEW OF OPERATING MODESThe WTT-110 can be set to operate in one of two distinct operating modes: PeakCapture or Average. In Peak Capture

Seite 9

– 7 –9.0 GENERAL OPERATING PROCEDURES1. Press On/Off key. During power-up, the WTT-110 performs a self-test routine. During this procedure, the maxim

Seite 10 - DJUSTING ADVANCED SETTINGS

– 8 –6. Insert the free end of the cable using a small amount of tension into the Wire Clamp Fixture and rotate the handle clockwise until the cable

Seite 11 - TERMINAL PULL TESTER

– 9 –9.10 Additional Operating InformationLow BatteryWhen battery charge is low, the LO BAT indicator will blink on and off in theLCD Display indicati

Weitere Dokumente für Messgeräte Checkline WTT-110

Um das Dokument anzuzeigen Checkline WTT-110 Bedienungsanleitung

Checkline WTT-110 Bedienungsanleitung (2 Seiten)

Kommentare zu diesen Handbüchern

Keine Kommentare

Checkline WTT-110 Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Messgeräte Checkline WTT-110 herunter. Checkline WTT-110 User Manual Benutzerhandbuch

Inhaltsverzeichnis

Weitere Dokumente für Messgeräte Checkline WTT-110

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Messgeräte Checkline WTT-110